®
ELECTRIC RANGE
Use & Care Guide
For questions about features, operation/performance
parts, accessories or service, call: 1-800-253-1301.
In Canada, call for assistance 1-800-461-5681, for installation
and service, call: 1-800-807-6777
or visit our website at...
Table of Contents................................................. 2
9757454
RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the
anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children
and adults.
Anti-Tip Bracket
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
Range Foot
3
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical
I Use Proper Pan Size – The range is equipped with
one or more surface units of different size. Select
utensils having flat bottoms large enough to cover
the surface unit heating element. The use of
undersized utensils will expose a portion of the
heating element to direct contact and may result in
ignition of clothing. Proper relationship of utensil to
burner will also improve efficiency.
shock, injury to persons, or damage when using the
range, follow basic precautions, including the
following:
I
WARNING: TO REDUCE THE RISK OF
TIPPING OF THE RANGE, THE RANGE MUST BE
SECURED BY PROPERLY INSTALLED ANTI-TIP
DEVICES. TO CHECK IF THE DEVICES ARE
INSTALLED PROPERLY, SLIDE RANGE FORWARD,
LOOK FOR ANTI-TIP BRACKET SECURELY
ATTACHED TO FLOOR, AND SLIDE RANGE BACK
SO REAR RANGE FOOT IS UNDER ANTI-TIP
BRACKET.
I Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy
spillovers that may ignite.
I Make Sure Reflector Pans or Drip Bowls Are in
Place – Absence of these pans or bowls during
cooking may subject wiring or components
underneath to damage.
I
CAUTION: Do not store items of interest to
children in cabinets above a range or on the
backguard of a range – children climbing on the
range to reach items could be seriously injured.
I Protective Liners – Do not use aluminum foil to line
surface unit drip bowls or oven bottoms, except as
suggested in the manual. Improper installation of
these liners may result in a risk of electric shock, or
fire.
I Proper Installation – Be sure the range is properly
installed and grounded by a qualified technician.
I Never Use the Range for Warming or Heating the
Room.
I Glazed Cooking Utensils – Only certain types of
glass, glass/ceramic, ceramic, earthenware, or other
glazed utensils are suitable for range-top service
without breaking due to the sudden change in
temperature.
I Do Not Leave Children Alone – Children should not
be left alone or unattended in area where the range
is in use. They should never be allowed to sit or
stand on any part of the range.
I Utensil Handles Should Be Turned Inward and Not
Extend Over Adjacent Surface Units – To reduce the
risk of burns, ignition of flammable materials, and
spillage due to unintentional contact with the utensil,
the handle of a utensil should be positioned so that
it is turned inward, and does not extend over
adjacent surface units.
I Wear Proper Apparel – Loose-fitting or hanging
garments should never be worn while using the
range.
I User Servicing – Do not repair or replace any part of
the range unless specifically recommended in the
manual. All other servicing should be referred to a
qualified technician.
I Do Not Soak Removable Heating Elements –
Heating elements should never be immersed in
water.
I Storage in or on the Range – Flammable materials
should not be stored in an oven or near surface
units.
I Do Not Cook on Broken Cooktop – If cooktop
should break, cleaning solutions and spillovers may
penetrate the broken cooktop and create a risk of
electric shock. Contact a qualified technician
immediately.
I Do Not Use Water on Grease Fires – Smother fire or
flame or use dry chemical or foam-type extinguisher.
I Use Only Dry Potholders – Moist or damp
potholders on hot surfaces may result in burns from
steam. Do not let potholder touch hot heating
elements. Do not use a towel or other bulky cloth.
I Clean Cooktop With Caution – If a wet sponge or
cloth is used to wipe spills on a hot cooking area,
be careful to avoid steam burn. Some cleaners can
produce noxious fumes if applied to a hot surface.
I DO NOT TOUCH SURFACE UNITS OR AREAS
NEAR UNITS – Surface units may be hot even
though they are dark in color. Areas near surface
units may become hot enough to cause burns.
During and after use, do not touch, or let clothing or
other flammable materials contact surface units or
areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and
surfaces facing the cooktop.
I Use Care When Opening Door – Let hot air or
steam escape before removing or replacing food.
I Do Not Heat Unopened Food Containers – Build-up
of pressure may cause container to burst and result
in injury.
SAVE THESE INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
For self-cleaning ranges –
I Keep Oven Vent Ducts Unobstructed.
I Do Not Clean Door Gasket – The door gasket is
essential for a good seal. Care should be taken not
to rub, damage, or move the gasket.
I Placement of Oven Racks – Always place oven
racks in desired location while oven is cool. If rack
must be moved while oven is hot, do not let
potholder contact hot heating element in oven.
I Do Not Use Oven Cleaners – No commercial oven
cleaner or oven liner protective coating of any kind
should be used in or around any part of the oven.
I DO NOT TOUCH HEATING ELEMENTS OR
INTERIOR SURFACES OF OVEN – Heating
elements may be hot even though they are dark in
color. Interior surfaces of an oven become hot
enough to cause burns. During and after use, do
not touch, or let clothing or other flammable
materials contact heating elements or interior
surfaces of oven until they have had sufficient time
to cool. Other surfaces of the appliance may
become hot enough to cause burns – among these
surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven
doors.
I Clean Only Parts Listed in Manual.
I Before Self-Cleaning the Oven – Remove broiler pan
and other utensils.
For units with ventilating hood –
I Clean Ventilating Hoods Frequently – Grease should
not be allowed to accumulate on hood or filter.
I When flaming foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list
of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and
requires businesses to warn of potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or
other reproductive harm.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde,
carbon monoxide, and toluene.
5
PARTS AND FEATURES
This manual covers several different models. The range you have purchased may have some or all of the items listed. The locations and
appearances of the features shown here may not match those of your model.
Control Panel
A
B
C
D
E
ACCUBAKE SYSTEM
OFF
OFF
OFF
OFF
HI
HI
HI
HI
LO
LO
LO
LO
MEDIUM
MEDIUM
MEDIUM
MEDIUM
F
G
H
I
A. Surface Locator Indicator
B. Power On Indicator Light
C. Electronic Oven Control
D. Power On Indicator Light
E. Surface Locator Indicator
F. Left Rear Control Knob
G. Left Front Control Knob
H. Right Front Control Knob
I. Right Rear Control Knob
Range
F
G
A
H
I
J
B
C
K
L
D
E
A. Surface Cooking Area
B. Oven Vent (not visible)
C. Anti-Tip Bracket
D. Model and Serial Number Plate
(behind left side of storage drawer)
E. Removable Storage Drawer
F. Hot Surface Indicator Light
G. Electronic Oven Control
H. Control Panel
I. Automatic Oven Light Switch
(beneath control panel)
J. Gasket
K. Broil Element (not visible)
L. Bake Element
6
COOKTOP USE
Cooktop Controls
Ceramic Glass Use
The surface cooking area will glow red when an element is on. It
will cycle on and off, at all settings, to maintain the selected heat
level.
WARNING
It is normal for the surface of white ceramic glass to appear to
change color when surface cooking areas are hot. As the glass
cools, it will return to its original color.
Wiping off the cooktop before and after each use will help keep it
free from stains and provide the most even heating. For more
information, see “General Cleaning” section.
I
I
I
Do not store jars or cans above the cooktop. Dropping a
heavy or hard object onto the cooktop could crack the
cooktop.
Fire Hazard
Do not leave a hot lid on the cooktop. As the cooktop cools,
air can become trapped between the lid and the cooktop,
and the ceramic glass could break when the lid is removed.
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly; then, while wearing oven mitts, remove the spills
while the surface is still warm. If sugary spills are allowed to
cool down, they can adhere to the cooktop and can cause
pitting and permanent marks.
Control knobs must be pushed in before turning them to a
setting. The controls can be set anywhere between HI and LO.
Use the following chart as a guide when setting heat levels.
SETTING
HI
RECOMMENDED USE
I
Do not slide cookware or bakeware across the cooktop.
Aluminum or copper bottoms and rough finishes on
cookware or bakeware could leave scratches or marks on the
cooktop.
I
I
To start foods cooking.
To bring liquids to a boil.
I
I
Do not cook popcorn in prepackaged aluminum containers
on the cooktop. They could leave aluminum marks that
cannot be removed completely.
Between
MEDIUM-HI
I
I
To hold a rapid boil.
To quickly brown or sear meat.
Do not allow objects that could melt, such as plastic or
aluminum foil, to touch any part of the entire cooktop.
MEDIUM
I
I
I
To cook gravy, pudding or sauce.
To fry poultry or meat.
I
I
Do not use the cooktop as a cutting board.
To maintain a slow boil.
Use cookware about the same size as the surface cooking
area. Cookware should not extend more than 1” (2.5 cm)
outside the area.
Between
I
I
To stew or steam food.
To simmer food.
LO-MEDIUM
B
LO
I
I
To keep foods warm.
To melt chocolate.
A
C
REMEMBER: When range is in use or (on some
models) during the Self-Cleaning cycle, the entire
cooktop area may become hot.
A. Surface Cooking Area
B. Cookware/Canner
C. 1” (2.5 cm) Maximum Overhang
I
I
Use flat-bottomed cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed or
dented bottoms could cause uneven heating and poor
cooking results.
Power On Indicator Lights
The Power On Indicator lights beside the control knobs indicate
which surface elements are turned on. A Power On Indicator light
will glow when its corresponding surface element is turned on.
Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the ruler,
no space or light should be visible between it and the
cookware.
I
I
Cookware designed with slightly indented bottoms or small
expansion channels can be used.
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
I
Do not cook foods directly on the cooktop.
7
HOT Surface Indicator Lights
Four HOT surface indicator lights.
I
Cookware
IMPORTANT: Never leave empty cookware on a hot surface
cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides, a well-
fitting lid and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop. Aluminum and copper
may be used as a core or base in cookware. However, when used
as a base it can leave permanent marks on the cooktop or grates.
The HOT surface indicator lights on the cooktop surface will glow
when their corresponding surface elements are turned on. The
HOT surface indicator lights will continue to glow as long as the
elements are too hot to touch, even after they are turned off.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
NOTE: Heat from the oven vent may cause the left rear HOT
surface indicator light to glow, showing that the cooktop is too
warm to touch.
Use the following chart as a guide for cookware material
characteristics.
Home Canning
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
COOKWARE
Aluminum
CHARACTERISTICS
I
I
I
Heats quickly and evenly.
I
Center the canner on the grate or largest surface cooking
area or element. Canners should not extend more than 1”
(2.5 cm) outside the cooking area.
Suitable for all types of cooking.
Medium or heavy thickness is best for
most cooking tasks.
I
Do not place canner on two surface cooking areas, elements
or surface burners at the same time.
Cast iron
I
I
I
Heats slowly and evenly.
I
I
On ceramic glass models, use only flat-bottomed canners.
Good for browning and frying.
Maintains heat for slow cooking.
On coil element models, the installation of a Canning Unit Kit
is recommended. If a kit is not installed, the life of the coil
element will be shortened.
Ceramic or
Ceramic glass
I
I
I
Follow manufacturer’s instructions.
I
For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
Heats slowly, but unevenly.
Ideal results on low to medium heat
settings.
Copper
I
Heats very quickly and evenly.
Earthenware
I
I
Follow manufacturer’s instructions.
Use on low heat settings.
Porcelain
enamel-
I
See stainless steel or cast iron.
on-steel or
cast iron
Stainless steel
I
I
Heats quickly, but unevenly.
A core or base of aluminum or copper
on stainless steel provides even
heating.
8
ELECTRONIC OVEN CONTROL
A
B
C
D
E
F
G
H
I
J
K
A. Oven Display
B. Timer Functions
C. Clock
E. Oven Settings
F. Temperature Adjustment
G. Auto Clean
I. Hour and Minute
J. Start and Control Lock
K. Off/Cancel
D. Oven Light
H. Timed Cooking
Display
Clock
When power is first supplied to the appliance, everything on the
display will light up for 1 to 2 seconds, then the time of day and
“PF” will appear. Press OFF/CANCEL to clear “PF” from the
display.
On some models, if you do not want the clock time to be
displayed, press and hold the CLOCK pad (button) for 5 seconds.
When the clock is not displayed, you can see the time for
5 seconds by pressing the CLOCK pad (button).
If “PF” appears at any other time, a power failure has occurred.
Press OFF/CANCEL and reset the clock if needed.
To Set:
Before setting, make sure the oven, TIMER and COOK TIME are
off.
When the oven is in use, the display shows preheat time and the
temperature and oven setting.
1. Press CLOCK.
When the oven is not in use, the display shows the time of day.
2. Press the HOUR “up” or “down” arrow pads (buttons) to set
When using the TIMER, for settings of 1 to 59 minutes, the
display will count down in seconds. For settings 1 hour or over,
the display will count down hours and minutes.
the time of day.
3. Press CLOCK or START.
When using COOK TIME, the display will show hours and
minutes. When using STOP TIME, the display will show minutes
and seconds.
Tones
Tones are audible signals which indicate that a function has been
entered correctly, or when a cycle has ended.
Start
To shut off all tones except the end-of-timer and error
tones:
1. Press and hold the STOP TIME button for 5 seconds.
After setting a function, you must press the START button to start
the function. If you do not press the START button within
5 seconds, “START?” will be displayed as a reminder.
2. A short tone will sound when the tones have been changed.
To turn tones back on, repeat Step 1.
3. “Off” will be displayed for 3 seconds when the tones have
been turned off, and “ON” will be displayed for 3 seconds
when the tones have been turned back on.
Off/Cancel
The OFF/CANCEL button stops any function except the Clock,
Timer and Control Lock. When you press the OFF/CANCEL
button, the display will show the time of day, or the time
remaining if the TIMER is being used.
Timer
The Timer can be set in hours or minutes up to 12 hours and
59 minutes, and counts down the set time.
NOTE: The Timer does not start or stop the oven.
To Set:
1. Press TIMER SET.
If no action is taken after 5 minutes, the display will return to
the time of day mode.
2. Press the HOUR “up” or “down” arrow pads (buttons) to set
the length of time.
9
3. Press START.
To Display Temperatures in °C instead of °F:
Press and hold the CUSTOM BROIL button for 5 seconds. A
short tone will sound, and the temperature display will switch to
°C. Repeat to switch back to °F.
If not pressed within 5 seconds, the display will return to the
time of day mode and the programmed function will be
canceled.
When the set time ends, end-of-cycle tones will sound, then,
if on, reminder tones will sound every minute.
OVEN USE
4. Press TIMER OFF anytime to cancel the Timer.
Remember, do not press the OFF/CANCEL pad (button)
because the oven will turn off.
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
To display the time of day when the timer is counting down, press
CLOCK.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well
ventilated room.
Control Lock
The Control Lock shuts down the control panel pads (buttons) to
prevent unintended use of the oven(s).
Aluminum Foil
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
When the control is locked, only the CLOCK, TIMER SET, TIMER
OFF, and OVEN LIGHT pads (buttons) will function.
The Control Lock is preset unlocked, but can be locked.
I
Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
To Lock/Unlock Control: Before locking, make sure the oven,
Timer and Timed Cooking (COOK TIME on some models) are off.
Press and hold START for 5 seconds, or until a single tone
sounds, “LOC” and a picture of a lock appear on the display.
Repeat to unlock and remove “LOC” from display.
I
To catch spills, place foil on rack below dish. Make sure foil is
at least 1” (2.5 cm) larger than the dish and that it is turned up
at the edges.
Oven Temperature Control
Positioning Racks and Bakeware
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door and element or
burner cycling may give incorrect readings.
IMPORTANT: Never place food or bakeware directly on the oven
door or bottom. Permanent damage will occur to the porcelain
finish.
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted. It can be changed in Fahrenheit or
Celsius.
RACKS
NOTES:
I
I
I
Position racks before turning the oven on.
Do not move racks with bakeware on them.
Make sure racks are level.
A minus sign means the oven will be cooler by the displayed
amount. No sign means the oven will be warmer by the displayed
amount. Use the following chart as a guide.
To move a rack, pull it out to the stop position, raise the front
edge, then lift out. Use the following illustration and chart as a
guide.
ADJUSTMENT °F
(ADJUSTMENT °C)
COOKS FOOD
5° to 10°F (3° to 6°C)
...a little more
...moderately more
...much more
15° to 20°F (9° to 12°C)
25° to 35°F (15° to 21°C)
-5° to -10°F (-3° to -6°C)
-15° to -20°F (-9° to -12°C)
-25° to -35°F (-15° to -21°C)
5
4
3
2
1
...a little less
...moderately less
...much less
To Adjust Oven Temperature Calibration:
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “0° CAL.”
FOOD
RACK POSITION
Frozen pies, large roasts, turkeys,
angel food cakes
1 or 2
2. Press the TEMP “up” or “down” arrow pads (buttons) to
increase or to decrease the temperature in 10°F (6°C)
amounts. The adjustment can be set between 30°F (18°C)
and -30°F (-18°C).
Bundt cakes, most quick breads,
yeast breads, casseroles, meats
2
3. Press START.
Cookies, biscuits, muffins, cakes,
nonfrozen pies
2 or 3
10
BAKEWARE
To cook food evenly, hot air must be able to circulate. Allow 2”
(5 cm) of space around bakeware and oven walls. Use the
following chart as a guide.
Oven Vent
NUMBER
OF PAN(S)
POSITION ON RACK
1
Center of rack.
2
Side by side or slightly staggered.
A
A. Oven vent (above door)
3 or 4
Opposite corners on each rack. Make sure
that no bakeware piece is directly over
another.
The oven vent should not be blocked or covered, because it
allows the release of hot air and moisture from the oven. Blocking
or covering the vent will cause poor air circulation, affecting
cooking and cleaning results. Never set plastics, paper or other
items that could melt or burn near the oven vent.
Bakeware
The bakeware material affects cooking results. Follow
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
Bake
The oven automatically regulates the heat levels and both the top
and bottom elements cycle on and off accordingly during preheat
and bake to maintain a precise temperature range for optimal
cooking results.
BAKEWARE/
RESULTS
RECOMMENDATIONS
Light colored
aluminum
I
Use temperature and time
recommended in recipe.
To Bake or Roast:
Before baking and roasting, position the racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven to preheat before putting food
in, unless it is recommended in the recipe.
I
Light golden
crusts
I
Even browning
1. Press BAKE.
Dark aluminum
and other
bakeware with
dark, dull and/or
nonstick finish
I
May need to reduce baking
temperatures 25°F (15°C).
Press the TEMP “up” or “down” arrow pads (buttons) to enter
a temperature other than 350°F (175°C). Press the “up” or
“down” pads (buttons) to raise or lower the temperature in
5°F/5°C increments.
I
I
Use suggested baking time.
For pies, breads and casseroles, use
temperature recommended in
recipe.
2. Press START.
I
Brown, crisp
crusts
A preheat time will count down, and “PrE” will appear on the
display. The oven control automatically sets preheating times
based on the oven temperature you select.
I
Place rack in center of oven.
Insulated cookie
sheets or baking
pans
I
I
Place in the bottom third of oven.
May need to increase baking time.
When the actual oven temperature is reached, the set
temperature will replace “PrE” on the display.
When the set temperature is reached, if on, one tone will
sound.
I
Little or no
bottom
3. Press OFF when finished cooking.
browning
The temperature can be changed any time after pressing START.
Stainless steel
I
May need to increase baking time.
Preheating
I
Light, golden
crusts
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ.
I
Uneven
browning
Waiting an additional 10 minutes after the preheat conditioning
time ends to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
Stoneware
I
I
Follow manufacturer’s instructions.
I
Crisp crusts
Ovenproof
glassware,
ceramic glass or
ceramic
May need to reduce baking
temperatures 25°F (15°C).
I
Brown, crisp
crusts
11
BROILING CHART
For best results, place food 3” (7 cm) or more from the broil
element. Times are guidelines only and may need to be adjusted
for individual foods and tastes. Recommended rack positions are
numbered from the bottom (1) to the top (4). Do not use position
5. For diagram, see the “Positioning Racks and Bakeware”
section.
Custom Broil
The top element operates at full power when heating.
Use this setting for normal broiling and top browning with the
door open in the Broil Stop position.
I
Use only the broiler pan and grid provided with the appliance.
It is designed to drain juices and help prevent spatter and
smoke.
COOK TIME
RACK
POSITION
minutes
I
For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
FOOD
SIDE 1
SIDE 2
Chicken
bone-in pieces
boneless breasts
I
I
Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to prevent curling.
3
4
17-20
11-16
17-20
11-16
Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
Fish
Fillets ¹ꢀ₄- ¹ꢀ₂”
(.6-1.25 cm) thick
Steaks ³ꢀ₄- 1”
(2-2.5 cm) thick
4
4
8-10
4-5
8-9
I
After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
16-18
Frankfurters
4
5-7
3-4
To Broil:
Before broiling, position the rack according to the Broiling Chart.
Ground meat patties*
³ꢀ₄” (2 cm) thick
well done
Position food on the grid in the broiler pan, then place it in the
center of the oven rack with the longest side parallel to the door.
It is not necessary to preheat the oven before putting food in,
unless it is recommended in the recipe.
4
4
4
4
13-14
8-10
7-8
Ham slice, precooked
¹ꢀ₂” (1.25 cm) thick
4-5
Leave the door partly open when you use the oven to broil. This
allows the oven to stay at the proper temperature.
Lamb chops
1” (2.5 cm) thick
1. Press CUSTOM BROIL.
2. Press START.
14-17
20-22
8-9
The set oven temperature will appear on the display until the
oven is turned off.
Pork chops
1” (2.5 cm) thick
10-11
3. Press OFF/CANCEL when finished cooking.
Steak
1” (2.5 cm) thick
medium rare
medium
To Vari Broil:
4
4
4
14-15
15-16
18-19
7-8
Changing the temperature when custom broiling allows more
precise control when cooking. The lower the temperature, the
slower the cooking. Thicker cuts and unevenly shaped pieces of
meat, fish and poultry may cook better at lower broiling
temperatures.
8-9
well done
9-10
*Place up to 9 patties, equally spaced, on broiler grid.
1. Press CUSTOM BROIL.
Press the TEMP “up” or “down” arrow pads (buttons) to enter
a temperature other than 500°F (260°C). The broil range can
be set between 300°F (150°C) and 525°F (275°C).
Convection Cooking
(on some models)
2. Press START.
In a convection oven, the fan-circulated hot air continually
distributes heat more evenly than the natural movement of air in a
standard thermal oven. This movement of hot air maintains a
consistent temperature throughout the oven, cooking foods more
evenly, crisping surfaces while sealing in moisture and yielding
crustier breads.
The set oven temperature will appear on the oven display
until the oven is turned off.
3. Press OFF/CANCEL when finished cooking.
Most foods can be cooked by lowering cooking temperatures
25°F to 50°F (14°C to 28°C) and cooking time can be shortened
by as much as 30 percent, especially for large turkeys and roasts.
I
I
I
It is important not to cover foods so that surface areas remain
exposed to the circulating air, allowing browning and crisping.
Keep heat loss to a minimum by opening the oven door only
when necessary.
Choose cookie sheets without sides and roasting pans with
lower sides to allow air to move freely around the food.
12
CONVECTION COOKING CHART
Convection Baking and Roasting
Food/Rack
Position
Cook Time
(min. per
1 lb [454 g])
Oven Temp.
Internal
Food Temp.
During convection baking or roasting, the bake and broil
elements cycle on and off in intervals to maintain the oven
temperature, while the fan constantly circulates the hot air.
Beef, Rack Position 2
Rib Roast
If the oven door is opened during convection baking or roasting,
the broil element and fan will turn off immediately and the bake
element will turn off in 2 minutes. They will come back on once
the door is closed.
rare
20-25
25-30
30-35
140°F (60°C)
300°F (149°C) 160°F (71°C)
170°F (77°C)
medium
well done
I
For optimal cooking results, do not use aluminum foil.
I
Reduce recipe temperature 25°F (14°C). The cook time may
need to be reduced also. See the cookbook supplied with
this oven for more information.
Rib Roast
(boneless)
rare
22-25
27-30
32-35
140°F (60°C)
300°F (149°C) 160°F (71°C)
170°F (77°C)
medium
well done
To Convection Bake or Roast:
Before convection baking or roasting, position the racks
according to the “Positioning Racks and Bakeware” section.
When using two racks, place them on rack positions 2 and 4.
Rump,
Sirloin Tip
Roast
rare
medium
well done
When roasting with CONVECT BAKE, use the roasting rack on
top of the broiler pan and grid. It is not necessary to wait for the
oven to preheat before putting food in, unless recommended in
the recipe.
20-25
25-30
30-35
300°F (149°C) 140°F (60°C)
160°F (71°C)
170°F (77°C)
Meat Loaf
20-25
325°F (163°C) 165°F (74°C)
A
Veal, Rack Position 2
Loin, Rib,
Rump
Roast
B
medium
well done
25-35
30-40
325°F (163°C) 160°F (71°C)
170°F (77°C)
C
Pork, Rack Position 2
Loin Roast
30-40
35-40
325°F (163°C) 160°F-170°F
(71°C-77°C)
A. Roasting rack
B. Broiler grid
C. Broiler pan
(boneless)
Shoulder
Roast
325°F (163°C) 160°F-170°F
(71°C-77°C)
1. Press CONVECT BAKE.
Press the TEMP “up” or “down” arrow pads to enter a
temperature other than 350°F (177°C). The convection bake
range can be set between 170°F and 500°F (77°C and
260°C).
Ham, Rack Position 2
Fresh
25-35
15-20
300°F (149°C) 160°F (71°C)
300°F (149°C) 160°F (71°C)
(uncooked)
2. Press START.
Fully
Cooked
A preheating time will count down on the display, and “PrE”
will appear. The oven control automatically sets preheating
time based on the oven temperature selected.
Lamb, Rack Position 2
As the preheating time ends, the set temperature replaces
“PrE” on the display. When the set temperature is reached, if
enabled, one tone will sound.
Leg,
Shoulder
Roast
medium
well done
The temperature settings can be changed any time after
pressing START. Changing the temperature will not change
the preheat countdown time.
25-30
30-35
300°F (149°C) 160°F (71°C)
170°F (77°C)
Chicken*, Rack Position 2
Whole
3. Press OFF/CANCEL when finished cooking.
3-5 lbs.
20-25
325°F (163°C) 180°F (82°C)
325°F (163°C) 180°F (82°C)
(1.5-2.2 kg)
5-7 lbs.
15-20
(2.2-3.1 kg)
13
2. Press STOP TIME (optional).
Food/Rack
Position
Cook Time
(min. per
1 lb [454 g])
Oven Temp.
Internal
Food Temp.
3. If STOP TIME has been pressed, press the HR and MIN “up”
or “down” arrow pads to enter the desired time to end
cooking.
4. Press START TIME.
Turkey*, Rack Positions 1 or 2
5. Press the HOUR “up” or “down” arrow pads to enter the time
13 lbs. and
under
10-15
300°F (149°C) 180°F (82°C)
of day to start.
6. Press START.
(5.85 kg)
“DELAY” will appear on the display.
Over 13 lbs.
(5.85 kg)
10-12
300°F (149°C) 180°F (82°C)
When the start time is reached, the oven will automatically
turn on.
Cornish Game Hens*, Rack Position 2 or 3
When the stop time is reached (if programmed), the oven will
shut off automatically and “End” will appear on the display.
1-1.5 lbs.
50-60
325°F (163°C) 180°F (82°C)
End-of-cycle tones will sound, then, if on, reminder tones will
sound every minute.
(0.5-0.7 kg)
*Do not stuff poultry when convection roasting.
7. Press OFF or open the oven door to clear the display and/or
stop reminder tones.
Timed Cooking
RANGE CARE
WARNING
Food Poisoning Hazard
Self-Cleaning Cycle
Do not let food sit in oven more than one hour
before or after cooking.
(on some models)
Doing so can result in food poisoning or
sickness.
WARNING
Timed Cooking allows the oven to be set to turn on at a certain
time of day, cook for a set length of time, and/or shut off
automatically. Delay start should not be used for food such as
breads and cakes because they may not bake properly.
To Set a Cook Time:
1. Press BAKE (optional).
Burn Hazard
Press the TEMP “up” or “down” arrow pads to enter a
temperature other than the one displayed.
Do not touch the oven during the
Self-Cleaning cycle.
2. Press STOP TIME.
3. Press the HOUR “up” or “down” arrow pads to enter the
Keep children away from oven during
Self-Cleaning cycle.
desired time to end cooking.
4. Press START.
Failure to follow these instructions can result
in burns.
The display will count down the time.
When the time ends, the oven will shut off automatically and
“End” will appear on the display.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well ventilated room.
End-of-cycle tones will sound, then, if on, reminder tones will
sound every minute.
5. Press OFF/CANCEL or open the oven door to clear the
display and/or stop reminder tones.
Self-clean the oven before it becomes heavily soiled. Heavy soil
results in longer cleaning and more smoke.
To Set a Delayed Cook Time:
Before setting, make sure the clock is set to the correct time of
day. See “Clock” section.
Keep the kitchen well-ventilated during the Self-Cleaning cycle to
help get rid of heat, odors, and smoke.
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see
“Oven Vent” or “Oven Vents” section.
1. Press desired cook function.
Press the TEMP “up” or “down” arrow pads to enter a
temperature other than the one displayed.
Do not clean, rub, damage or move the oven door gasket. The
door gasket is essential for a good seal.
14
Prepare Oven:
To Delay Start Self-Clean:
Before delay starting Self-Clean, make sure the clock is set to the
correct time of day. See “Clock” section. Also, make sure the
door is closed completely or it will not lock and the cycle will not
begin.
I
I
I
I
Remove the broiler pan, grid, cookware and bakeware and,
on some models, the temperature probe from the oven.
Remove any foil from the oven because it may burn or melt,
damaging the oven.
1. Press AUTO CLEAN.
Remove oven racks to keep them shiny and easy to slide.
See “General Cleaning” section for more information.
Press the hour and minute pads (buttons) to set a clean time
other than 3 hours 30 minutes. You can select a time between
2 hours 30 minutes and 4 hours 30 minutes. The last
Hand clean inside door edge and the 1½” (3.8 cm) area
around the inside oven cavity frame, being careful not to
move or bend the gasket. This area does not get hot enough
during self-cleaning to remove soil. Do not let water, cleaner,
etc. enter slots on door frame. Use a damp cloth to clean this
area.
30 minutes of the self-cleaning cycle is a cool down period.
2. Set the start time.
Press the “up” or “down” pads (buttons) until the correct time
shows on the display. The oven will automatically determine
the stop time by adding the set cleaning time to the set start
time.
I
Wipe out any loose soil to reduce smoke and avoid damage.
At high temperatures, foods react with porcelain. Staining,
etching, pitting or faint white spots can result. This will not
affect cooking performance.
3. Press START.
When the start time is reached, the oven will automatically
turn on.
When the cycle is complete and the oven cools, “End” will
appear on the oven display and “DOOR LOCKED” or
“LOCKED” will disappear from the display.
Prepare Cooktop and Storage Drawer:
I
Remove plastic items from the cooktop because they may
melt.
4. Press OFF/CANCEL to clear the oven display.
I
Remove all items from the storage drawer.
To Stop Self-Clean any time:
Press OFF/CANCEL. If the oven temperature is too high, the door
will remain locked. It will not unlock until the oven cools.
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
The Self-Cleaning cycle uses very high temperatures, burning soil
to a powdery ash.
The oven is preset for a 3 hour 30 minute clean cycle, however
the time can be changed. Suggested clean times are 2 hours
30 minutes for light soil and between 3 hours 30 minutes to
4 hours 30 minutes for average to heavy soil.
Once the oven has completely cooled, remove ash with a damp
cloth. Do not wipe down any of the inside surfaces until the oven
has completely cooled down. Applying a cool damp cloth to the
inner door glass before it has completely cooled could result in
the glass breaking.
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions
on cleaning products.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
EXTERIOR PORCELAIN ENAMEL SURFACES
(on some models)
The oven light will not work during the Self-Cleaning cycle.
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire appliance is cool. These spills
may affect the finish.
To Self-Clean:
Before self-cleaning, make sure the door is closed completely or
it will not lock and the cycle will not begin.
I
Glass cleaner, mild liquid cleaner or nonabrasive scrubbing
pad:
1. Press AUTO CLEAN.
Gently clean around the model and serial number plate
because scrubbing may remove numbers.
Press the hour and minute pads (buttons) to set a clean time
other than 3 hours 30 minutes. You can select a time between
2 hours 30 minutes and 4 hours 30 minutes. The last
30 minutes of the self-cleaning cycle is a cool down period.
STAINLESS STEEL (on some models)
2. Press START.
Do not use soap-filled scouring pads, abrasive cleaners, Cooktop
Polishing Creme, steel-wool pads, gritty washcloths or some
paper towels. Damage may occur.
The oven door will automatically lock and “DOOR LOCKED”
or “LOCKED,” and the start time will appear on the oven
display. The door will not unlock until the oven cools.
Rub in direction of grain to avoid damaging.
When the cycle is complete and the oven cools, “End” will
appear on the oven display and “DOOR LOCKED” or
“LOCKED” will disappear from the display.
I
I
I
Stainless Steel Cleaner & Polish (not included):
See “Assistance or Service” section to order.
Liquid detergent or all-purpose cleaner:
Rinse with clean water and dry with soft, lint-free cloth.
Vinegar for hard water spots
3. Press any pad or open the oven door to clear the oven
display.
15
CERAMIC GLASS (on some models)
CONTROL PANEL
Do not use steel wool, abrasive powder cleansers, chlorine
bleach, rust remover or ammonia because damage may occur.
Do not use abrasive cleaners, steel-wool pads, gritty washcloths
or some paper towels. Damage may occur.
Always wipe with a clean, wet cloth or sponge and dry thoroughly
to prevent streaking and staining.
I
Glass cleaner and soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
Cooktop Polishing Creme is recommended regularly to help
prevent scratches, pitting and abrasions and to condition the
cooktop, and can be ordered as an accessory. See “Assistance
or Service” to order.
OVEN DOOR EXTERIOR
A Cooktop Scraper is also recommended for stubborn soils, and
can be ordered as an accessory. See “Assistance or Service” to
order. The Cooktop Scraper uses razor blades. Store razor
blades out of the reach of children.
I
Glass cleaner and paper towels or nonabrasive plastic
scrubbing pad:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
Light to moderate soil
I
Paper towels or clean damp sponge:
OVEN CAVITY
Clean while the cooktop is still warm. You may want to wear
oven mitts while doing so.
Do not use oven cleaners.
Sugary spills (jellies, candy, syrup)
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
I
Cooktop Scraper:
Clean while the cooktop is still warm. You may want to wear
oven mitts while doing so.
I
I
I
Self-Cleaning cycle:
See “Self-Cleaning Cycle” first.
I
Cooktop Polishing Creme and clean damp paper towel:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth. Continue
rubbing until white film disappears.
OVEN AND ROASTING RACKS
Self-Cleaning cycle:
Heavy soil, dark streaks, specks and discoloration
See “Self-Cleaning Cycle” first. Remove racks or they will
discolor and become harder to slide. If this happens, a light
coating of vegetable oil applied to the rack guides will help
them slide.
I
Cooktop Polishing Creme or nonabrasive cleanser:
Rub product into soil with a damp paper towel or soft cloth.
Continue rubbing until white film disappears.
Steel-wool pad
Burned-on soil
I
Cooktop Polishing Creme and Cooktop Scraper:
BROILER PAN AND GRID
Rub creme into soil with damp paper towel. Hold scraper as
flat as possible on surface and scrape. Repeat for stubborn
spots. Polish entire cooktop with creme and paper towel.
Do not clean in the Self-Cleaning cycle.
I
Mildly abrasive cleanser:
Metal marks from aluminum and copper
Scrub with wet scouring pad.
I
Cooktop Polishing Creme:
I
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth. Continue
rubbing until white film disappears. The marks will not totally
disappear but after many cleanings become less noticeable.
Soak for 20 minutes, then scrub with scouring or steel-wool
pad.
I
Oven cleaner:
Tiny scratches and abrasions
Follow product label instructions.
I
Cooktop Polishing Creme:
Porcelain enamel only, not chrome
Rub creme into surface with a damp paper towel or soft
cloth. Continue rubbing until white film disappears. Scratches
and abrasions do not affect cooking performance and after
many cleanings become less noticeable.
I
Dishwasher
STORAGE DRAWER ( on some models)
Make sure drawer is cool and empty before cleaning.
COOKTOP CONTROLS
For more information, see “Storage Drawer” section.
Do not use steel wool, abrasive cleansers or oven cleaner.
Do not soak knobs.
I
Mild detergent
When replacing knobs, make sure knobs are in the Off position.
On some models, do not remove seals under knobs.
I
Soap and water or dishwasher:
Pull knobs straight away from control panel to remove.
16
To Replace:
1. Insert both hanger arms into the door.
Oven Light
(on some models)
The oven light is a standard 15-watt appliance bulb. It will come
on when the oven door is open. It will not work during the Self-
Cleaning cycle (on some models). On some models, when the
oven door is closed, press OVEN LIGHT to turn it on or off.
Before replacing, make sure the oven and cooktop are cool and
the control knobs are off.
To replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
2. Open the oven door.
counterclockwise to remove.
You should hear a “click” as the door is set into place.
Move the hinge levers back to the locked position. Ensure that
the door is free to open and close. If it is not, repeat the removal
and installation procedures.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb and bulb cover by turning clockwise.
5. Plug in range or reconnect power.
Storage Drawer
The storage drawer can be removed. Before removing, make sure
drawer is cool and empty.
To remove:
1. Pull drawer straight out to the first stop.
2. Lift up the back of the drawer and pull out.
To replace:
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is off
and cool. Then, follow these instructions. The oven door is heavy.
1. Fit the ends of the drawer rails into the guides in
the cavity.
To Remove:
1. Open oven door all the way.
2. Slide the drawer closed.
2. Flip up the hinge latch on each side.
Sweep-Thru Base
When the storage drawer is removed, the sweep-thru base
makes cleaning easier and provides access to the leveling legs.
3. Close the oven door as far as it will shut.
4. Lift the oven door while holding both sides.
A
Continue to push the oven door closed and pull it away from
the oven door frame.
A. Sweep-thru base
17
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate
Oven indicator lights flash
I
I
Is the power supply cord unplugged? Plug into a grounded
I
Do the oven indicator lights flash? See the “Electronic
Oven Control” section. If the indicator light(s) keeps flashing,
call for service. See “Assistance or Service” section.
outlet.
Has a household fuse blown or has the circuit breaker
tripped? Replace the fuse or reset the circuit.
Display shows messages
Cooktop will not operate
I
I
Is the display showing “PF”? There has been a power
failure. Clear the display. See “Display(s)” section. On some
models, reset the clock, if needed. See “Clock” section.
I
I
Is the control knob set correctly? Push in knob before
turning to a setting.
Is the display showing a letter followed by a number?
Depending on your model, press OFF/CANCEL, OFF or
CANCEL/OFF to clear the display. See “Display(s)” section. If
it reappears, call for service. See “Assistance or Service”
section.
Excessive heat around cookware on cooktop
Is the cookware the proper size? Use cookware about the
same size as the surface cooking area, element or surface
burner. Cookware should not extend more than 1 in. (2.5 cm)
outside the cooking area.
Self-Cleaning Cycle will not operate
I
I
Is the oven door open? Close the oven door all the way.
Hot Surface indicator light stays on
Has the function been entered? See “Self-Cleaning Cycle”
section.
I
Does the Hot Surface indicator light stay on after control
knob(s) have been turned off? See “Cooktop Controls”
section.
I
I
On some models, has a delay start Self-Clean cycle been
set? See “Self-Cleaning Cycle” section.
Has a delay start been set? See “Timed Cooking” or “Delay
Start” section, depending on your model.
Cooktop cooking results not what expected
I
I
I
Is the proper cookware being used? See “Cookware”
Oven cooking results not what expected
section.
Is the control knob set to the proper heat level? See
“Cooktop Controls” section.
I
I
I
I
I
I
I
I
I
I
Is the appliance level? Level the appliance. See the
Installation Instructions.
Is the appliance level? Level the appliance. See the
Installation Instructions.
Is the proper temperature set? Double-check the recipe in
a reliable cookbook.
Is the proper oven temperature calibration set? See “Oven
Temperature Control” section.
Oven will not operate
Was the oven preheated? See “Bake,” “Custom Broil,” and
“Convection Baking and Roasting” sections.
I
Is the electronic oven control set correctly? See
“Electronic Oven Control” section.
Is the proper bakeware being used? See “Bakeware”
section.
I
I
Has a delay start been set? See “Timed Cooking” section.
On some models, is the Control Lock set? See “Control
Lock” section.
Are the racks positioned properly? See “Positioning Racks
and Bakeware” section.
Is there proper air circulation around bakeware? See
“Positioning Racks and Bakeware” section.
Oven temperature too high or too low
Is the batter evenly distributed in the pan? Check to make
sure batter is level in the pan.
I
I
Does the oven temperature calibration need adjustment?
See “Oven Temperature Control” section.
Is the proper length of time being used? Adjust cooking
time.
On slide-in models, does the cooling fan run during Bake,
Broil or Clean? It is normal for the fan to automatically run
when the oven is in use. This helps cool the electronic
control.
Has the oven door been opened while cooking? Oven
peeking releases oven heat and can result in longer cooking
times.
I
I
Are baked items too brown on the bottom? Move rack to
higher position in the oven.
Are pie crust edges browning early? Use aluminum foil to
cover the edge of the crust.
18
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Whirlpool Brand Home Appliances
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
If you need replacement parts
Please include a daytime phone number in your correspondence.
If you need to order replacement parts, we recommend that you
use only FSP® replacement parts. FSP® replacement parts will fit
right and work right because they are made with the same
precision used to build every new WHIRLPOOL® appliance.
In Canada
For product related questions, please call the Whirlpool Canada
Inc. Customer Interaction Center toll free:
1-800-461-5681
To locate FSP® replacement parts in your area, call our Customer
Interaction Center telephone number or your nearest Whirlpool
designated service center.
Monday to Friday 8:00 a.m. - 6:00 p.m. (EST).
Saturday 8:30 a.m. - 4:30 p.m. (EST).
In the U.S.A.
Our consultants provide assistance with:
I
Features and specifications on our full line of appliances.
Call the Whirlpool Customer Interaction Center
toll free: 1-800-253-1301.
I
Referrals to local dealers.
Our consultants provide assistance with:
For parts, accessories and service in Canada
I
I
I
I
I
Features and specifications on our full line of appliances.
Call 1-800-807-6777. Whirlpool Canada Inc. designated service
technicians are trained to fulfill the product warranty and provide
after-warranty service, anywhere in Canada.
Installation information.
Use and maintenance procedures.
Accessory and repair parts sales.
For further assistance
If you need further assistance, you can write to Whirlpool Canada
Inc. with any questions or concerns at:
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Customer Interaction Center
Whirlpool Canada Inc.
I
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
19
WHIRLPOOL® COOKTOP, BUILT-IN OVEN AND RANGE WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor costs to correct defects in
materials or workmanship. Service must be provided by a Whirlpool designated service company.
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CLEANTOP® COOKTOP
On ceramic glass ranges and ceramic glass cooktops, in the second through fifth years from the date of purchase, when this appliance
is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for FSP®
replacement parts for the CLEANTOP® ceramic glass cooktop.
Whirlpool Corporation warrants that the ceramic glass cooktop will not discolor, the cooktop pattern will not wear off, the rubber seal
between the ceramic glass cooktop and porcelain edge will not crack, the ceramic glass cooktop will not crack due to thermal shock
and the surface unit elements will not burn out.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace house fuses or
correct house wiring, or to replace owner-accessible light bulbs.
2. Repairs when your appliance is used in other than normal, single-family household use.
3. Pickup and delivery. Your appliance is designed to be repaired in the home.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God or use of products not
approved by Whirlpool Corporation or Whirlpool Canada Inc.
5. Repairs to CLEANTOP® ceramic glass cooktop if it has not been cared for as recommended in the Use & Care Guide.
6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
7. Replacement parts or repair labor costs for units operated outside the United States or Canada.
8. In Canada, travel or transportation expenses for customers who reside in remote areas.
9. Any labor costs during the limited warranty period.
WHIRLPOOL CORPORATION AND WHIRLPOOL CANADA INC. SHALL NOT BE LIABLE
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation
may not apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from state to
state or province to province.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine
if another warranty applies.
If you need service, first see the “Troubleshooting” section of this book. After checking “Troubleshooting,” additional help can be found
by checking the “Assistance or Service” section or by calling the Whirlpool Customer Interaction Center, 1-800-253-1301 (toll-free),
from anywhere in the U.S.A. For parts and service in Canada, please call 1-800-807-6777. For product-related questions in Canada,
please call 1-800-461-5681.
5/00
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Write down the following information about your appliance to
better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label/plate, located on your appliance as shown in the
“Parts and Features” section.
9757454
© 2004 Whirlpool Corporation.
2/04
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A., Whirlpool Canada Inc. Licensee in Canada
|