U
DVD / VIDEO CD / CD PLAYER
DVD-S540
OWNER’S MANUAL
STANDBY
/ON
FCC INFORMATION (for US customers only)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly
approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the
USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not
result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used accord-
ing to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with
FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference,
which can be determined by turning the product "OFF" and "ON", please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial
type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you
can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6600 Orangethorpe Ave. Buena Park, CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association's Consumer Electronics Group want you to get the most out of
your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion - and, most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic
Industries Association's Consumer Electronics Group recommend you to avoid prolonged exposure from excessive
volume levels.
For Customer Use:
CAUTION- Visible and invisible laser
radiation when open. Avoid exposure to beam.
Read carefully the information located at the rear panel of the
player and enter below the Serial No. Retain this information for
CAUTION Visible and invisible laser radiation
-
future reference.
when open. Avoid exposure to beam.
MODEL NO.
120 VOLTS 20 WATTS 60Hz
MADE IN CHINA
Model No.
Serial No. __________________________
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to wide slot and
fully insert.
This Class B digital apparatus complies with Canadian ICES-003.
CAUTION
Use of controls or adjustments or
performance of procedures other than
those specified herein may result in
hazardous radiation exposure.
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus as set out in the Radio Interference
Regulations of the Canadian Department of Communications.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
To assure the finest performance, please read
this manual carefully. Keep it in a safe place for
future reference.
14 Do not attempt to modify or fix this unit.
Contact qualifiedYAMAHA service personnel
when any service is needed.The cabinet should
never be opened for any reason.
15 When not planning to use this unit for long
periods of time (i.e., vacation), disconnect the AC
power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING”
section on common operating errors before
concluding that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to
set the unit in standby mode, then disconnect
the AC power plug from the wall outlet.
Install this unit in a well ventilated, cool, dry, clean
place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet,
allow about 2.5cm (1 inch) of free space all
around this unit for adequate ventilation.
Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
Do not expose this unit to sudden temperature
changes from cold to hot, nor locate this unit in
an environment with high humidity (i.e., a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit in a location where
foreign objects may fall onto this unit or where
this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause
damage and/or discoloration on the surface
of this unit.
3
4
WARNING
TO REDUCETHE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSETHIS UNITTO
RAIN OR MOISTURE.
5
NOTE:
Pictures shown maybe different between countries.
Never make or change connections with the power
switched on.
– Burning objects (i.e., candles), as they may
cause fire, damage to this unit, and/or
personal injury.
When playing DTS encoded CDs, excessive noise
will be heard from the analog stereo outputs.To
avoid possible damage to the audio system, the
consumer should take proper precautions when the
analog stereo outputs of the player are connected to
an amplification system.To enjoy DTS Digital
Surround™ playback, an external 5.1-channel DTS
Digital Surround™ decoder system must be
connected to the digital output of the player.
– Containers with liquid in them, as they may
fall, spilling the liquid and causing an electrical
shock to the user and/or damage to this unit.
Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
6
LASER SAFETY
7
8
9
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may
overheat, possibly causing damage.
Do not use excessive force on switches, knobs
and/or cords.
This unit employs a laser. Due to possible eye injury,
only a qualified service person should remove the
cover or attempt to service this device.
CAUTION
10 When disconnecting the power cord from the
wall outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using
this unit with a higher voltage than specified is
dangerous and may cause fire, damage to this
unit, and/or personal injury.YAMAHA will not be
held responsible for any damage resulting from
use of this unit with a voltage other than as
specified.
VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN.AVOID EXPOSURETO BEAM
(WARNING LOCATION: INSIDE ON LASER
COVERSHIELD ORTHE BACKPLATE OF SET)
LASER
Type
Wave length
Semiconductor laser GaAlAs
650 nm (DVD)
780 nm (VCD/CD)
7 mW (DVD)
Output Power
10 mW (VCD/CD)
Beam divergence 60 degree
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an
electrical storm.
Introduction
Thank you for purchasing this unit. This Owner’s
Manual explains the basic operation of this unit.
Cleaning discs
● When a disc becomes dirty, clean it with a
cleaning cloth. Wipe the disc from the centre out.
Do not wipe in a circular motion.
● Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
The region code is 1 for U.S.A and
Canada models.
1
Since it is usual for DVD movies to
be released at different times in
different regions of the world, all players have
region codes and discs can have an optional
region code. This unit can play discs containing the
identical region code, or mentioned as region
“ALL”. If you load a disc of a different region code
to this unit, you will see the region code notice on
the screen. The disc will not playback, and should
be unloaded.
Symbols Used in this Manual
The below symbols appear in some headings and
notes with the following meanings:
– Description refers to playback of
DVD-video discs
DVD
– Description refers to playback of
Video CDs
VCD
Environmental Information
– Description refers to playback of
Audio CDs
This unit consists of materials which can be
recycled and reused if disassembled by a
CD
specialised company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old equipment.
– Description refers to playback of
SuperVCDs
SSVVCCDD
● Some DVD video discs require specific
functions or allow only limited functions
during playback.
● “ Ä” may appears on the TV screen
which means that the function is not
available on that specific DVD video disc.
Supplied accessories
– Remote control
– Batteries (two AA size) for remote control
– Audio/Video cable
– Owner’s Manual
Notes about discs
– This unit is designed for use with DVD video,
Video CD, Super video CD, Audio CD, CD-R, CD-RW
(MP3 Supported), DVD+RW, DVD+R, DVD-R and
DVD-RW.
– CD-R and CD-RW cannot be played unless
finalized.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
– Some discs cannot be played depending on the
recording conditions such as PC environment and
application software. The characteristics and
condition of the discs; materials, scratches,
curvature, and etc, may result in failure.
– Be sure to use only CD-R and CD-RW discs made
by reliable manufacturers.
– Do not use any non standard shaped discs (heart,
etc.)
– Do not use disc with tape, scals, or paste on it,
damage to the unit may result.
”DTS” and ”DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
– Do not use a disc printed on its surface by a
commercially available label printer.
2
Functional Overview
Front and Rear Panels
STANDBY/ON
– to turn this unit to standby mode or
ON
R/T
– search forward* / go to the next
chapter or track
DiscTray
S/Q
– search backward* / go to a previous
chapter or track
/ OPEN/CLOSE
– to open/close the disc tray
9STOP
– to stop playback
B/ ; PLAY/PAUSE
– to start/interrupt playback
STANDBY
/ON
* Press button for about two seconds.
S-VIDEO
AC Power Cord
– connect to S-Video input of your AV
receiver
– connect to a standard AC outlet
AUDIO OUT (Left/Right)
– connect to AUDIO inputs of your
AV receiver or stereo system
COMPONENTVIDEO
– connect to component video inputs of
your AV receiver
OPTICAL
– connect to DIGITAL INPUT of your
AV receiver
VIDEO
– connect to Video inputs of your AV
receiver
COAXIAL
– connect to DIGITAL INPUT of your
AV receiver
Y
VIDEO
L
R
S
VIDEO
P
R
P
B
COAXIAL
PCM
OPTICAL
DIGITAL
COMPONENT
VIDEO OUT
DTS MPEG
DIGITAL OUT
AUDIO OUT
Caution: Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
3
Functional Overview
Remote Control
|
TOP MENU/RETURN
– display the top-level disc menu
(DVD) / go back to previous
menu (VCD)
B/
– turn this unit ON or go to
standby-on mode
1
2
5
8
0
3
6
4
0-9 numeric buttons
– select numbered items in a
menu
MENU
– access menu of a disc (DVD) /
switch PBC on/off (VCD)
7
9
TOP MENU RETURN
ON SCREEN
MENU
SETUP
ON SCREEN
1 2 3 4
– (left/right/up/down) select an
item in the menu
– access or remove player’s On
Screen Display menu
ENTER
OK
SETUP
STOP
PLAY
PAUSE
ENTER/OK
– access or remove player’s setup
menu
– acknowledge menu selection
SUBTITLE ANGLE ZOOM AUDIO
REPEAT
A
B
SCAN MUTE
S
– search backward* / go to a
previous chapter or track
T
DVD
– search forward* / next chapter
or track
STOP ( 9)
– stop playback
SUBTITLE
– subtitle language selector
PLAY ( B)
– start playback
ANGLE
– select DVD camera angle
PAUSE ( ;)
– pause playback temporarily /
frame-by-frame playback
ZOOM
– enlarge video image
AUDIO
REPEAT
– repeat chapter, track, title, disc /
shuffle chapter, track
– audio language and format
selector
A-B
– repeat a specific segment
SCAN
– preview the content of a track
or whole disc (VCD) / play the
first 6 seconds or less of each
track (CD)
MUTE
– disable or enable sound output
* Press and hold button for about two seconds.
4
Preparation
Note:
General Notes on connections
– If the audio format of the digital output does not
match the capabilities of your receiver, the receiver
will produce a strong, distorted sound or no sound at
all. Make sure to select the appropriate audio
format at menu screen included on the disc.
Pressing AUDIO once or more may change not only
audio languages but also audio formats, and the
selected format appears for several seconds on the
status window.
Never make or change connections with the
power switched on.
● Depending on the equipment you wish to
connect, there are various ways you could
connect this unit. Possible connections are shown
in the following drawings.
● Please refer to the manuals of other equipment as
necessary to make the best connections.
● Do not connect this unit via your VCR. The video
quality could be distorted by the copy protection
system.
Analog Connections
Use audio/video cable supplied with this unit to
connect AUDIO OUT L (left) and R (right) jacks
of this unit to corresponding input jacks of your
audio equipment such as Stereo amplifier.
● Do not connect this unit’s audio out jack to the
phono in jack of your audio system.
Digital Connections
Y
VIDEO
This unit has COAXIAL and OPTICAL digital out
jacks. Connect one or both of them to your AV
receiver equipped with Dolby digital, DTS, or
MPEG decoder using each specific cable (separate
purchase).
L
R
S
VIDEO
PR
PB
COAXIAL
PCM
DTS MPEG
OPTICAL
DIGITAL
COMPONENT
VIDEO OUT
DIGITAL OUT
AUDIO OUT
R
L
(supplied)
Y
VIDEO
L
R
S
VIDEO
PR
PB
COAXIAL
PCM
OPTICAL
DIGITAL
COMPONENT
VIDEO OUT
DTS MPEG
DIGITAL OUT
AUDIO OUT
C
O
R
L
1
CD/DVD
Stereo
amplifier
R
L
COAXIAL
IN
OPTICAL
IN
AV receiver
Left
speaker
Right
speaker
Subwoofer
Center speaker
Left main
speaker
Right main
speaker
Left rear
speaker
Right rear
speaker
You will need to set this unit’s digital
output to All (see ‘Digital Output’).
5
Preparation
S-Video terminal <A>
Video Connections
S (separate) video connection achieves a clearer
picture than composite video connection by
separating color and luminance when transmitting
signals. Use commercially available S-video cable.
Receiver (and TV) with S-video input is required.
If your AV receiver has video output jacks,
connect your receiver (and then to your TV) so
that you can use one TV for several different
video sources (LD, VCR etc.) by simply switching
the input source selector of your receiver.
The player has three types of video output jacks.
Use one of them in accordance with the input
jacks of the equipment to be connected.
Component Video terminal <B>
Component video connection achieves high
fidelity in reproducing colors (better performance
than S-video connection), separating video signal
into luminance (Y, terminal color-coded as green),
and color difference (Pb, blue/Pr, red). Use
commercially available coaxial cables. Receiver
(and TV) with component input is required.
Observe the color of each jack when connecting.
If your receiver does not have component output
jacks, connecting the player’s component output
directly to your TV’s component input can
reproduce better video image.
Y
VIDEO
L
R
S
VIDEO
PR
PB
COAXIAL
PCM
OPTICAL
DIGITAL
COMPONENT
VIDEO OUT
DTS MPEG
DIGITAL OUT
AUDIO OUT
(supplied)
V
<A>
<B>
<C>
S
Y
PBCB
PRCR
S VIDEO
INPUT
COMPONENT
VIDEO IN
VIDEO
Composite Video terminal (1, 2) <C>
Use audio/video cable supplied with this unit
when connecting the player to a TV.
AV receiver
VIDEO
OUT
COMPONENT
S VIDEO
VIDEO OUT OUT
VIDEO 1, 2 jacks of VIDEO OUT output the
same signal. You can connect one to your
receiver’s input using supplied Audio/Video cable,
and the other to another receiver or a TV.
VIDEO
IN
COMPONENT
VIDEO IN
S VIDEO
IN
6
Preparation
Inserting batteries into the
Remote Control
Open the battery cover by pressing in the tab,
then lift off the cover.
Insert batteries with the correct polarity as
indicated by the + and - symbols inside the
battery compartment.
NTSC/PAL Conversion
This player is equipped with a NTSC/PAL
conversion feature to convert the video output of
the disc to match your TV system. The
conversions supported are as below. To activate
the conversion, refer to “TV Type”:
1
2
Disc
Output format
Selected mode
NTSC
3
Close the cover.
Type
DVD
Format
PAL
PAL
MULTI
NTSC
NTSC
PAL
NTSC
NTSC
NTSC
NTSC
PAL
PAL
PAL
PAL
-
+
NTSC
PAL
NTSC
PAL
VCD
Notes:
+
-
– “Multi” can only be selected when using a TV that
has both the NTSC and PAL systems.
– Slight picture distortions may occur due to this
conversion. This is normal. Thus, the “Multi” is most
suitable for the best picture quality.
CAUTION!
– Remove batteries if they are exhausted or
not to be used for a long time.
– Do not use old and new or different types
of batteries in combination.
– Batteries contain chemical substances, so
they should be disposed off properly and
kept away from children.
Turning on the power
1
2
3
Connect the AC power cord to the power outlet.
Turn on the TV and your AV receiver.
Select the appropriate input source at the AV
receiver that was used to connect to this unit.
Refer to the equipment owner’s manual for detail.
Turn this unit on.
Set the TV to the correct Video IN channel. (eg.
EXT1, EXT2, AV1, AV2, AUDIO/VIDEO, etc.
(Refer to your TV owner’s manual for detail)
● The front display lights up and the default
screen appears on the TV.
Using the Remote Control
● Direct the remote control at the remote sensor
of the DVD player.
● Do not drop or give the remote control a shock.
● Do not leave the remote control in extremely hot
or humid places.
4
5
● Do not spill water or put anything wet on the
remote control.
Smart Power On/Off
When in STOP or NO DISC mode, the DVD
player will switch to standby mode after 15
minutes without any operations for saving energy.
It is easily reactivated by pressing the POWER or
PLAY on the remote control or the STANDBY/
ON button on the front panel.
7
Operation
3
To go directly to any chapter/track, enter the
chapter/track number using the numeric buttons
and press ENTER/OK.
Basic Playback
Press STANDBY/ON on the front panel to turn
on the DVD player.
Press /(OPEN/CLOSE) on the front panel to
open disc loading tray.
Place the chosen disc in the tray, with the label
facing up.
Press /(OPEN/CLOSE) again to close the tray.
● After recognizing this disc, the player begin to
playback automatically.
1
2
3
4
Note: Long press of the ¡1or 2™till switch on
backward or forward search.
DVD VCD CD SVCD
SEARCH
1
2
3
To search the contents in fast speed, press 2or
1for fast forward/backward searching.
Press 2or 1again to increase the speed for
searching.
Press PLAY to return to normal playback.
Slow Motion
DVD
1
2
3
To get a slow motion effect during playback, press
3or 4.
Press 3or 4again, you can get different playback
forward/backward speeds.
Press PLAY to return to normal play back.
Notes:
VCD SVCD
– DVDs may have a region code. Your player will
not play discs that have a region code different from
the region code of your player.
– If ‘Disc Lock’ is set to LOCK and the disc inserted
is not authorized, the 6-digit code must be entered
and/or the disc must be authorized (see ‘Disc Lock’).
1
2
3
To get a slow motion effect during playback, press
4.
Press 4again, you can get different playback
forward speeds.
Press PLAY to return to normal play back.
Note: The SLOW BACKWARD function is not
available for VCD/Super VCD discs.
General Operation
Note: All instructions set out below refer to the
remote control, unless otherwise stated.
Audio control during playback
DVD VCD CD SVCD
MUTE
Video control during playback
1
2
Press MUTE to disable the sound output.
Press MUTE again to deactivate the mute.
DVD VCD CD SVCD
STOP
1
You can resume the play from the point at which
you stopped last time, if you just press STOP
once. It will start from the beginning if you press
STOP twice to stop playback.
Audio channel selection
VCD CD SVCD
1
Super VCD has two stereo audio channels which
are used for playing karaoke or the audio language
selection. ( for instance, you can choose one
channel for only the music background of the
song while you play the karaoke.)
Press AUDIO to select the audio channels you
want.
VCD has only one stereo audio channel, you can
select STEREO, MONO LEFT, MONO RIGHT or
MIX-MONO by pressing AUDIO.
DVD VCD CD SVCD
PAUSE/STEP
1
2
3
To get a still picture, press PAUSE during
playback.
To step forward to the next frame picture, press
PAUSE again.
2
3
To resume normal playback, press PLAY.
SKIP
● Stereo: Output the left and right audio
channels of the disc through the left and right
audio jacks accordingly.
● Mono Left: Output the left audio channels of
the disc through the left and right audio jacks.
1
Press ¡1or 2™briefly during playback to go to
the next chapter/track or to return to the
beginning of the currect chapter/track
respectively.
Press ¡1twice briefly to step back to the
previous chapter/track.
2
8
Operation
● Mono Right: Output the right audio channels
of the disc through the left and right audio jacks.
● MIX-Mono: each of the audio jacks can output
the same audio effect as stereo.
OSD (On-Screen Display)
This function will provide some information about
your playing disc on the screen.
● Press ON SCREEN.
The Status window appears on the TV.
Repeat and Shuffle
DVD VCD
Title/Chapter/Track selection
DVD
1
Press 34to select “Title” or “Chapter” (DVD) or
“Track” (VCD).
Press ENTER/OK.
Select a title, chapter or track number using the
numeric buttons.
● Each time you press REPEAT, the Repeat/Shuffle
2
3
mode changes as follows;
Chapter Repeat*
Title Repeat
Shuffle
DVD VCD
Repeat/Shuffle Off Shuffle Repeat
Time Search
1
Press 34to select “TT Time” or “CH
Time”(DVD) or “Track Time” or “Disc
Time”(VCD).
● “TT Time” refers to the total time of the
current title, and the “CH Time” refers to the
total time of the current chapter.
Press ENTER/OK.
* This feature may not be available with some
discs.
VCD CD
With PBC OFF,
● Each time you press REPEAT, the Repeat/Shuffle
mode changes as follows;
2
3
Enter hours, minutes and seconds from left to
right using the numeric buttons. (e.g. 0:34:27)
Track Repeat
Disc Repeat
Shuffle Repeat Shuffle
Repeat/Shuffle Off
DVD
Audio/Subtitle/Angle
You can change “Audio”, “Subtitle” or “Angle” if
available on the disc you are playing.
Press 34to select “Audio”, “Subtitle” or “Angle”.
Press ENTER/OK.
For Audio and Subtitle,
Press 34to highlight your selection and press
ENTER/OK.
DVD VCD CD
Repeat A-B
1
2
3
DVD-Video Discs: repeat a sequence in a title
Video and Audio CDs: repeat a sequence in a
track
Press Repeat A-B at your chosen starting point.
Press Repeat A-B again at your chosen end point.
● The repeat sequence begins.
1
2
or
For Angle,
3
To exit the sequence, press Repeat A-B.
Select an angle using the numeric buttons.
DVD VCD
Repeat/Time Display
DVD VCD CD SVCD
Disc Resume
1
2
3
Press 34to select “Repeat” or “Time Disp.”.
Press ENTER/OK.
Press 34to highlight your selection and press
ENTER/OK.
This player can resume playback of the last 5 discs,
even if the disc was ejected or the power
switched off.
Load one disc, which is one of the last 5 discs.
Press PLAY when DVD player is recognizing the
disc. If the information of this disc has been stored
in the memory of DVD player, it will be played
back from the stop point last time.
1
2
CD
Time display
Each time you press ON SCREEN, the time
display changes as follows;
Total Elapsed
Single Remain
Total Remain
Single Elapsed
9
Operation
DVD VCD SVCD
Zoom
Changing the Audio Language and/or
format
● Press AUDIO repeatedly to select the different
DVD
The Zoom function allows you to change the
image size.
1
2
Press ZOOM to activate the function.
● Use 3412to view other parts of the
zoomed picture.
● Playback will continue.
Press ZOOM repeatedly to return to the original
size.
languages.
Note: The function will be activated only if the DVD
is recorded with multi-language audio tracks.
DVD SVCD
Subtitles
● Press SUBTITLE repeatedly to select the different
subtitles.
Special DVD Features
Note: The function will be activated, only if the DVD
or Super VCD is recorded with multi-subtitles.
DVD
Playing a Title
A DVD disc may have one or more titles. This
depends on the content (a movie, video clips, a
drama series, etc.) on the disc.
Special VCD & SVCD Features
Playback Control (PBC)
PBC function allows you to enter the index menu
which is used to select a track after loading the
VCD & SVCD disc.
● After you load a disc, information about the
content shows on the screen waiting for your
selection. You can also press TOP MENU to turn
back to the title menu during playback.
● Press the appropriate numeric buttons or
3412to highlight your selection.
If you want to activate the function during the
playback or after pressing STOP twice,
● Press ENTER/OK to confirm.
1
2
Press MENU to set the PBC On.
● Pay attention to the hint on the screen.
Use ¡1or 2™to select the page you like.
● If the items of the index menus are numbered,
press the appropriate numeric buttons.
● Press ENTER/OK.
DVD
Playing a Chapter
When you have selected a title, it may include one
or more chapters.
● Any time you want to watch another chapter
during playback, press MENU to turn back to the
chapter menu (If disc has chapter menu).
● Press the appropriate numeric buttons or
3412on the remote control to highlight your
selection.
3
Press RETURN to enter the index menu during
the playback.
Notes:
– The content of the index menu depends on the
disc. Please refer to the disc’s instructions for details.
– If the disc doesn’t include the PBC information,
this function will have no effect.
● Press ENTER/OK.
● After a chapter has been selected, you also
can press ¡1or 2™to make a change.
If you want to skip the index menu and
playback directly from the beginning,
DVD
Camera Angle
1
Press MENU to switch off the function.
Some discs contain scenes which have been shot
simultaneously from various angles.
This DVD player allows you to select the desired
camera angle.
● Press ANGLE on your remote control.
Note: The function is available only for the DVD
discs which have several angles recorded.
10
Operation
2
Disc Interval
Preview Function
This function is used to divide a disc into six parts
by regular intervals and display them on one page
to help you preview the whole disc.
● Press SCAN to enter previewing menu.
● Press 34to highlight Track Digest, Disc Interval
or Track Interval.
● Press ENTER/OK to open one option.
● After you enter the menu of any digest type,
● To quit preview function: Press 3412to
highlight EXIT and press ENTER/OK.
- To choose the desired track, press 3412to
highlight the second line and input your numerical
selection next to “SELECT” and press ENTER/
OK.
● To return to the previewing menu for
selecting the other digest type: Press 3412to
highlight MENU and press ENTER/OK.
3
Track Interval
Note: You can select Track Interval only during
playback, with PBC Off.
This function is used to divide a single track into
six parts by regular intervals and display them on
one page to help you preview the selected track.
1
Track Digest
This function will minimize the picture of every
track in order to display every six of these tracks
on the screen to help you know the content of
every track on the disc.
- To choose the desired track, please press 3412
to highlight the second line and input your
numerical selection next to “SELECT” and press
ENTER/OK.
- To choose the desired track, press 3412to
highlight the second line and input your selected
track number next to “SELECT”.
● Select the others from the current six by
pressing the ¡1or 2™to open the previous or
next page and press ENTER/OK.
11
Picture CD & MP3 Playback
This player can playback JPEG format pictures and
MP3 files on a personally recorded CD-R/RW
disc or commercial CD, and is compatible with
Kodak Picture CD.
Play Mode
Auto Playback
If you choose WITHOUT MENU, the DVD
player will automatically playback Picture CD/MP3
CD in sequence when it is loaded.
● Playback pictures or songs one by one
automatically.
● Album and track selection.
Repeat / Shuffle
● Repeat (disc / album / track / picture).
● Select any music or pictures from the disc to
playback them together.
● Maximum files numbers in one folder is 500.
● Maximum files Programmable is 100.
● When the Picture CD/MP3 CD menu is shown
on the screen, Press REPEAT repeatedly, the
button beside PLAY MODE will display different
option,
● Repeat Folder: All files in this folder will be
replayed time after time.
● Shuffle: All files in this folder will be played at
random without any repeat.
General Operation
● If you choose WITH MENU in the Setup Menu
(Please refer to the MP3 & JPEG navigator below),
the Picture CD/MP3 CD menu will be shown on
the screen before playback.
● Folder: All files in this folder will be played.
● If you press REPEAT during playback, the option
will be displayed on the screen accordingly.
● During Shuffle mode, you can skip tracks by
pressing ¡1or 2™.
● At any time during JPEG playback, press MENU to
return to the menu.
● To open the selected folder, press ENTER/OK.
● The menu shows six files or folders at a time. To
move to the next (or previous) page, press 2™
(or ¡1).
MP3 & JPEG Navigator
To select a different playback method, follow the
steps below.
1
At STOP mode, press SETUP to open the setup
menu.
2
3
4
5
6
Press 12to highlight PREFERENCE icon.
Press 4to open the PREFERENCE menu.
Press 34to highlight the MP3/JPEG NAV menu.
Press 2to enter the menu.
Press 34to highlight the WITHOUT MENU or
WITH MENU item.
● WITHOUT MENU: automatically playback all
files in according date sequence.
● WITH MENU: playback files in the selected
folder.
7
Press ENTER/OK to confirm your selection.
12
Picture CD & MP3 Playback
Playback with multi-angles
Special JPEG Features
Function Introduction
Picture CD is a disc with a collection of JPEG
format pictures, and all extension filenames
should end with ‘JPG’. The CD can be recorded
on any computer, and pictures may be from digital
camera or scanner. If the customers prefer, they
can make this CD become a Digital Album.
When displaying one picture on TV screen
● Press 3412to get different effects.
3: Flip the picture vertically.
4: Flip the picture horizontally.
1: rotate the picture anti-clockwise.
2: rotate the picture clockwise.
Wipe Effect
● Press ANGLE repeatedly to choose different
You can choose any general function introduced
in General Operation, besides, you also can,
● Display the thumbnails of 12 pictures.
● Zoom the picture.
● Rotate the picture.
● Flip the picture vertically or horizontally.
● Scan pictures by different effects.
wipe effects.
Special MP3 Features
Function Introduction
“MP3” stands for “MPEG Audio Layer-3”. and is a
part of the MPEG standard. A CD can store up to
10 hours of MP3 audio, which is nearly 10 times
as much as an Audio CD. Each song is recorded
as a file. You can choose any general function
introduced in General Operation. You can also
choose different playback speeds.
Preview Function
This function shows the content of the current
folder or the whole disc.
Press STOP during playback of JPEG pictures. You
will see the thumbnails of 12 pictures on the
screen.
1
JPEG and MP3 simultaneous
playback
1
2
Firstly playback MP3 music according to the
instructions introduced in playback Selection.
Then select a picture to playback. Refer to the
instructions introduced in playback Selection.
● Now the pictures will be played back in
sequence together with MP3 music.
2
3
Press ¡1or 2™to display the other pictures on
the next or the previous page.
Press 3412to highlight one of them and press
ENTER/OK to playback, or,
3
To quit simultaneous playback, press MENU to
return to the Picture CD/MP3 CD menu, then
pictures will be stopped. After that, press STOP,
then MP3 music will be stopped as well.
Move the cursor to highlight
on the
bottom of the page to start playback from the first
picture on the current page.
Press MENU to go to the Picture CD/MP3 CD
menu.
Note: In the function of JPEG and MP3 Simultaneous
Playback, ¡1and 2™are invalid for MP3.
4
Zoom picture
● During playback, press ZOOM to display the
picture with different scales.
● Press 3412to view the rest of the zoomed
picture.
13
Setup Menu
Program (not for Picture CD/MP3)
press 34to choose “Program”.
Press 2to move the cursor to the field of the
submenu to choose the item Input menu.
● Input menu: Enter the Program item.
Press ENTER/OK to enter the program page.
Basic Operation
Press SETUP in the STOP mode to enter the
Setup Menu.
Press ENTER/OK to go to the next level submenu
or confirm your selection.
Press 12to enter the submenu or return to the
previous menu.
1
2
1
2
3
3
4
5
Press 34to highlight the desired menu.
Press SETUP to quit the setup menu.
● When you quit the setup menu, the settings
will be stored in the player’s memory even if the
player is switched to power off.
Input your favorite track
1
2
Input valid track number by pressing the numeric
buttons.
Press 3412to move the cursor to the next
selected position.
● If the track number is more than ten, press 2™
to open the next page and go on programing, or
press 3412to highlight NEXT button, and then
press ENTER/OK.
General Setup menu
Some settings need to be made in this menu.
They are: “Disc Lock”, “Program”, “OSD
Language” and “Screen Saver”.
Follow the steps below:
3
Repeat this steps to input another track number
until the whole program is completed.
Remove a track
1
2
Press 3412to move the cursor to the track you
want to remove.
Press ENTER/OK or PLAY to remove this track
from the program menu.
1
2
Press SETUP to enter the setup menu.
Press 12to choose the GENERAL SETUP icon
Playback tracks
.
When programing is completed,
Press 3412to move the cursor to the START
button.
Press ENTER/OK.
● DVD player will playback the selected tracks
under the programed sequence.
1
2
Disc Lock
When the disc is locked, the player will store its
specific code into the memory for future
identification. For the next playback, the DVD
player will prompt you to enter the password.
Then, press ENTER/OK to load the disc.
Press 34to highlight “Disc Lock”.
Quit the program playback
In the Program menu,
1
2
1
2
Press 3412to move the cursor to the EXIT
button.
Press ENTER/OK to quit this menu.
Enter its submenu by pressing 2.
● Lock: Lock the disc being played.
● Unlock: unlock the disc.
3
Press 1to return to the General Setup Page.
Stop the program playback
● During playback of the programmed tracks, press
STOP. Then after you press PLAY, the DVD
player will resume normal playback.
14
Setup Menu
Repeat the program playback
Audio Setup menu
There are items included in Audio Setup Page
such as “Speaker Setup”, “Digital Audio Setup”,
“Equalizer” and “3D”.
● During playback of the programmed tracks, press
REPEAT. The programed tracks can be played
again.
Note: If you select Shuffle mode by pressing REPEAT
several times, the DVD player cancels program
playback.
OSD language
This option is to select a language for information
displayed on TV screen.
1
Press 34to highlight “OSD Language” in the
General Setup menu.
2
3
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected language.
1
2
Press SETUP to enter the setup menu.
Press 12to choose the AUDIO SETUP icon
.
4
5
Press ENTER/OK to confirm.
Press 1to return to the General Setup Page.
Speaker Setup
This menu contains setup options for your analog
audio output, such as “Downmix”, “D.R.C.”
(Dynamic Range Compression) etc. which makes
the setup system reproduce high quality surround
sound.
Screen Saver
This function is used to turn the screen saver on
or off.
Press 34to highlight “Screen Saver” in the
General Setup menu.
1
Downmix
2
3
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected item.
● On: In STOP or No DISC mode, if no actions
are performed within 5~6 minutes, the screen
saver will be activated.
● Off: Screen saver is disabled.
Press ENTER/OK.
Press 1to return to the General Setup Page.
1
2
3
Press 34to highlight the “Downmix”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected item.
● LT/RT
● This option should be used only if your DVD
player is connected to a Dolby Prologic decoder.
● Stereo
● This option will downmix Dolby Digital signals
directly into analogue stereo from L/R jacks.
● Virtual Surround
4
5
● This option will reproduce the surround
channels virtually.
4
5
Press ENTER/OK.
Press 1to return to the Audio Setup Page.
D.R.C. (Dynamic Range Compression)
The DVD player will compress the dynamic range
of its sound output for late-night listening.
Press 34to highlight “D.R.C.”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected item.
1
2
3
● On: Enable D.R.C.
● Off: Disable D.R.C.
4
5
Press ENTER/OK.
Press 1to return to the Audio Setup Page.
15
Setup Menu
Digital Audio Setup
Equalizer (Sound Mode)
In this menu, you can set up the digital audio
output signal from the digital jacks, such as coaxial
etc.
The “Equalizer” allow you to select from various
preset modes that control the frequency bands of
sound to optimize certain musical styles.
It greatly enhances the excitement and enjoyment
of your favourite music.
Press 34to highlight the “Equalizer”.
Enter its submenu “Sound Mode” by pressing 2.
Press 2.
Move the cursor by pressing 34to highlight the
selected item.
● None: Playback the disc under the original
sound effect.
Digital Output
1
2
3
Press 34to highlight Digital Output.
Enter its submenu by pressing 2.
1
2
3
4
Press 34to highlight the selected item.
● All: Original digital signals output. In this mode,
all audio settings except MUTE are invalid.
● PCM Only: If your receiver is PCM-
compatible, or your receiver can not decode
MPEG-2, Dolby Digital, or DTS audio, choose this
option.
5
6
Press ENTER/OK.
Press 1to return to the Audio Setup Page.
4
5
Press ENTER/OK.
Press 1and return to the Audio Setup Page.
3D (Reverb Mode)
Note: If Digital Output is set to All, all audio settings
except MUTE are invalid.
The “3D” can simulate the echoes and
frequency response of some particular places so
as to make you feel like personally on the place.
Press 34to highlight the “3D”.
Enter its submenu “Reverb Mode” by pressing 2.
Press 2.
Move the cursor by pressing 34to highlight the
selected item.
● Off: Playback the disc under the original sound
effect.
LPCM Output
1
2
3
4
In this menu, you can select PCM digital output
between 48kHz and 96kHz.
Press 34to highlight the LPCM Output.
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected item.
● 48K: 96kHz (if available on disc) PCM data
stream will be converted to 48kHz.
● 96K: If the 96kHz disc is copy protected, the
disital output will be muted to comply with the
standards.
1
2
3
5
6
Press ENTER/OK.
Press 1to return to the Audio Setup Page.
4
5
Press ENTER/OK.
Press 1to return to the Audio Setup Page.
16
Setup Menu
TV Display
Video Setup menu
There are items included in Video Setup menu
such as “TV Type”, “TV Display”, “Closed
Caption”, “Progressive” and “Picture Setting”.
4:3
PANSCAN
4:3
LETTERBOX
16:9
1
2
Press SETUP to enter the setup menu.
Press 12to choose the VIDEO SETUP icon
.
Select the aspect ratio of the TV to be connected.
4:3 PANSCAN ● when you connect a normal
TV to the DVD player. Displays the wide picture
on the whole TV screen with a portion
automatically cut off.
4:3 LETTERBOX ● when you connect a
normal TV to the DVD player. Displays a wide
picture with bands displayed on the upper and
lower portions of the TV screen.
TV Type
Before viewing the DVD or VCD, ensure that the
PAL or NTSC setting of the system matches your
TV set.
Press 34to highlight “TV Type” in the Video
Setup menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight one
option.
1
2
3
16:9 ● when you connect a wide-screen TV to
the DVD player.
4
5
Press ENTER/OK.
Press 1to return to the Video Setup Page.
Setup the item as follows,
1
Press 34to highlight the “TV Display” option in
the Video Setup menu.
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected item.
Note: Choosing NTSC item indicates that the player
will output NTSC signals, Similarly, you can get PAL
signals by choosing the PAL option. The option Multi
means video output depends on the format of the
DVD or VCD discs.
2
3
4
5
Press ENTER/OK.
Press 1to return to the Video Setup Page.
17
Setup Menu
Closed Caption
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE
DISPLAYED IN THE PICTURE. IN CASE OF 525
PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH
THE CONNECTION TO THE “STANDARD
DEFINITION” OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR VIDEO
MONITOR COMPATIBILITY WITH THIS
MODEL 525P DVD PLAYER, PLEASE CONTACT
OUR CUSTOMER SERVICE CENTER.
Closed captions are data that are hidden in the
video signal on specific discs, invisible without a
special decoder. The difference between subtitles
and captions is that subtitles are intended for
hearing persons and captions are for the hearing
impaired. Subtitles rarely show all of the audio.
For example, captions show sound effects (e.g.,
“phone ringing” and “footsteps”), while subtitles
don’t.
Before you select this function, please ensure that
the disc contains closed captions information and
your TV set also has this function.
Press 34to highlight “Closed Caption” in the
Video Setup menu.
1
This unit is compatible with the complete line of
YAMAHA products, including the projectors DPX-
1, DPX-1000, LPX-500 and the plasma monitor
PDM-1.
2
3
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight one
option.
● On: Enable Closed Caption.
● Off: Disable Closed Caption.
Press ENTER/OK.
Picture Setting
4
5
Press 1to return to the Video Setup Page.
In this menu, you can personalize your picture
color by adjusting brightness, contrast, tint and
color (saturation).
Press 34to highlight “Picture Setting” in the
Video Setup menu.
Progressive
1
This player’s COMPONENT video jack can
output progressive signals to a progressive signal
compatible TV for an extra high-quality picture.
Press 34to highlight “Progressive”.
Enter its submenu by pressing 2.
Move the cursor by pressing 34to highlight one
option.
2
Press 2to open its submenu.
1
2
3
Brightness
1
2
Press 34to highlight “Brightness”.
Press 2to open the level bar.
● On: Enable Progressive.
● Off: Disable Progressive.
BRIGHTNESS
-1
If you select “On”, the player prompt you to
comfirm your selection.
Press ENTER/OK.
3
4
Press 12to increase and decrease the brightness
level.
Press ENTER/OK to return to the Picture Setting
menu.
4
5
Press 1to return to the Video Setup Page.
Notes on activating Progressive:
Contrast
● Ensure that your TV has progressive scan.
● Connect with YPbPr video cable.
● When the Progressive is active, the VIDEO
(CVBS) and S VIDEO jacks do not output video
signals.
1
2
3
Press 34to highlight “Contrast”.
Press 2to open the level bar.
Press 12to increase and decrease the contrast
level.
Press ENTER/OK to return to the Picture Setting
menu.
4
● If there is no picture, wait 15 seconds for auto
recover or disactivate Progressive manually.
1
Open the disc tray by pressing /(OPEN/
CLOSE)on the front panel.
Press 1.
Tint
1
2
3
4
Press 34to highlight “Tint”.
2
3
Press 2to open the level bar.
Press 12to increase and decrease the tint level.
Press ENTER/OK to return to the Picture Setting
menu.
Press MUTE.
18
Setup Menu
Color (saturation)
Password Setup
This item is used for the parental control and disc
lock. Enter your six digit password when a hint is
displayed on the screen.
1
2
3
Press 34to highlight “Color”.
Press 2to open the level bar.
Press 12to increase and decrease the color
level.
4
Press ENTER/OK to return to the Picture Setting
menu.
1
2
3
4
5
Press SETUP to enter the setup menu.
Press 12to choose the PASSWORD icon
Press 4to highlight “Password”.
Press 2to highlight “Change”.
Press ENTER/OK to open the Password Change
Page.
.
6
Press 4to repeatedly until the player prompt you
to enter the old password.
7
8
9
Enter the current 6 digit code.
If successful, the player will prompt for a new one.
After that, enter the new password again to
reconfirm.
10 Press ENTER/OK to return to the Password
Setup Page.
Notes:
– You can change the setup of parental control and
load a locked disc with a valid password being
entered.
– If you forget your password, you can enter the
default password 842100, then you can input your
password after logging on.
19
Setup Menu
Disc Menu language
Preference Setup menu
DVD discs are available with multiple disc menu
languages. This option is used to select the default
disc menu language.
Press 34to highlight “Disc Menu”.
Enter the submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected item.
There are options included in this menu such as
“Audio”, “Subtitle”, “Disc Menu”, “Parental”,
“Default” and “MP3/JPEG NAV”.
1
2
3
● If you want to choose other languages, please
refer to the following instructions.
Press ENTER/OK.
4
5
Press 1to return to the Preference Page.
Note: If your DVD disc doesn’t include the disc menu
language you have set, the player will use another
recorded language instead.
1
2
3
Press STOP twice.
Press SETUP to enter the setup menu.
Press 12to choose the PREFERENCE icon
.
If you choose Others in Audio, Subtitle or
Disc Menu menu,
Audio language
DVD discs are available with multiple audio
languages. Use this option to select the preferred
default audio language.
Press 34to highlight “Audio”.
Enter the submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected option.
● If you want to choose other languages, please
refer to the instructions on the next page.
Press ENTER/OK.
You can select other languages. Please do as
follows,
Move the cursor by pressing 34to highlight
“Others”.
Press ENTER/OK.
● The DVD player will prompt you to enter a
language code (Four digits).
Input a language code by pressing numeric
buttons.
● Please look up the preferred language code in
the chapter LANGUAGE CODE, which can be
found at the end of this manual.
Press ENTER/OK.
1
2
1
2
3
3
4
4
5
Press 1to return to the Preference Page.
Note: Your DVD disc may not include the audio
language which you set in the AUDIO menu. If so,
the player will use another audio language instead.
Subtitle language
DVD discs are available with multi-subtitle
languages. Use this option to select the preferred
default subtitle language.
1
2
3
Press 34to highlight “Subtitle”.
Enter the submenu by pressing 2.
Move the cursor by pressing 34to highlight the
selected option.
● If you want to choose other languages, please
refer to the following instructions.
Press ENTER/OK.
4
5
Press 1to return to the Preference Page.
Note: Your DVD disc may not include the subtitle
which you set in the SUBTITLE menu. If so, the
player will use another subtitle language instead.
20
Setup Menu
DVD
Parental Control
Default Setup
Movies on DVDs may contain scenes which are
not suitable for children. Therefore, discs may
contain ‘Parental Control’ information which
applies to the complete disc or to certain scenes
on the disc. These scenes are rated from 1 to 8,
and alternative, more suitable scenes are available
on the disc. Ratings are country dependent. The
‘Parental Control’ feature allows you to prevent
discs from being played by your children or to
have certain discs played with alternative scenes.
● VCD, SVCD, CD have no level indication, so
parental control function has no effect on those
kinds of discs. This applies to most illegal DVD
discs.
If problems occur while setting up the DVD
player, the “Default” function can be used to reset
all options to the factory defaults and all your
personal settings will be erased.
Press 34to highlight “Default”.
Highlight RESET by pressing 2.
1
2
3
Press ENTER/OK.
Note: When this function is activated, all setups will
be reset to factory defaults.
MP3/JPEG Navigator
This menu allows you to select alternate settings
when you playback picture CD and MP3 CD.
Press 34to highlight MP3/JPEG NAV.
Press 2to enter the submenu.
Press 34to highlight WITHOUT MENU or
WITH MENU.
● WITHOUT MENU: playback all pictures or
MP3 music in sequence automatically.
● WITH MENU: playback pictures or MP3
music in the selected folder.
● You can follow the steps below to setup the
parental control:
1
2
3
1
2
3
Press 34to highlight “Parental”.
Move to its submenu by pressing 2.
Then use 34to highlight a rating for the disc
inserted.
4
Press ENTER/OK to confirm, then press 1to
return to the Preference Page.
4
Press ENTER/OK to confirm your selection.
No Parental Control
Parental Control is not activated. The Disc will be
played in full.
1
2
Select 8 ADULT item.
Press ENTER/OK.
Ratings 1 to 7:
3
Some discs contain scenes which are not suitable
for children. All scenes with a rating higher than
you set will be skipped during playback. However
if the disc contains alternate scenes, these will play
automatically. If not, the playback will stop and the
six digits code will need to be entered again.
21
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, set this unit to the
standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer
or service center.
Problem
Solution
No power
No picture
–
Check if the AC power cord is properly connected.
–
–
–
Check if the TV is switched on.
Check the video connection.
If you did not use Progressive Scan connections (using the Y PB
PR jacks on the DVD Player) and you do not have a picture at the
TV, please follow the steps below to turn off Progressive Scan;
1. Press /(OPEN/CLOSE) to open the disc tray.
2. Press 2.
3. Then press MUTE to deactivate the Progressive. The DVD
Player will reset itself to Component/Interlaced video. The disc
tray will closed automatically to let you know it has reset itself.
Distorted picture
–
–
The disc is badly scratched or dirty.
Sometimes a small amount of picture distortion may appear.
This is not a malfunction.
Completely distorted picture or black/
white picture with DVD or Video CD
–
Make sure the NTSC/PAL setting at the DVD player matches the
video signal of your television. (See NTSC/PAL CONVERSION)
No sound or distorted sound
–
–
Adjust the volume.
Check that the speakers are connected correctly.
No audio at digital output
–
–
Check the digital connections.
Check if your receiver can decode MPEG-2 or DTS and if not,
please make sure the digital output is set to PCM.
Check if the audio format of the selected audio language matches
your receiver capabilities.
–
–
Disc can’t be played
The DVD+R/DVD+RW/DVD-R/DVD-RW/CD-R/CD-RW
must be finalized.
–
–
–
Ensure the disc label is facing up.
Check if the disc is defective by trying another disc.
If you have recorded this particular Picture CD or MP3 CD
yourself, please ensure that your disc contains at least about 6~10
pictures or 3~5MP3 music tracks before using it with the player.
No return to start-up screen when
disc is removed
–
–
Reset the unit by switching the player off, then on again.
The player does not respond to the
remote control
Aim the remote control directly at the sensor on the front of the
player.
–
–
–
Reduce the distance to the player.
Replace the batteries in the remote control.
Insert the batteries with their polarities (+/– signs) as indicated.
Buttons do not work
–
–
–
In order to completely reset the player, unplug the AC cord from
the AC outlet.
Player does not respond to some
operating commands during playback
Operations may not be permitted by the disc. Refer to the
instructions of the disc.
DVD Video player cannot read CDs/
DVDs
Use a commonly available cleaning CD/DVD to clean the lens
before sending the DVD Video player for repair.
22
Specifications
PLAYBACK SYSTEM
AUDIO PERFORMANCE
DVD Video
DA Converter
24bit
Video CD & SVCD
CD
Signal-Noise (1 kHz)
Dynamic range (1 kHz)
105dB
100dB
PICTURE CD
CD-R, CD-RW
DVD+R, DVD+RW
DVD-R, DVD-RW
DVD
fs 96 kHz
fs 48 kHz
fs 48 kHz
fs 44.1kHz
fs 44.1kHz
2Hz- 44kHz
2Hz- 22kHz
2Hz- 22kHz
2Hz- 20kHz
2Hz- 20kHz
0.003%
SVCD
CD/VCD
Distortion and Noise (1 kHz)
VIDEO PERFORMANCE
Video (CVBS) Output
S-Video output
1 Vpp into 75 ohm
Y: 1 Vpp into 75 ohm
C: 0.3 Vpp into 75 ohm
TV STANDARD (PAL/50Hz) (NTSC/60Hz)
Number of lines
Playback
625
525
Component video output Y: 1 Vpp into 75 ohm
Pb/Cb Pr/Cr: 0.7 Vpp into
75 ohm
Black Level Shift
Video Shift
Multistandard (PAL/NTSC)
CONNECTIONS
On/Off
Left/Right
Y Output
Cinch (green)
Cinch (blue)
Cinch (red)
Mini DIN, 4 pins
Cinch
Cinch
1 coaxial, 1 optical
IEC958 for CDDA / LPCM/
MPEG1
Pb/Cb Output
Pr/Cr Output
S-Video Output
Video Output
Audio Output (L+R)
Digital Output
AUDIO FORMAT
Digital Mpeg/ AC-3/ DTS Compressed Digital
PCM
16, 20, 24 bits
fs, 44.1, 48, 96 kHz
24, 32, 56, 64, 96, 128, 256 kbps
fs, 16, 22.05, 24, 32, 44.1, 48 kHz
MP3(ISO 9660)
Analog Sound Stereo
IEC1937 for MPEG 2, Dolby
Digital and DTS
CABINET
Dimensions (w x d x h)
Weight
435 x 302 x 75 mm
Approx. 2.8 Kg
POWER SUPPLY
Specifications subject to change without prior notice.
Power inlet
Power usage
Power usage standby
120V, 60Hz
Approx. 12W
< 1W
Maintenance
Cleaning the Cabinet
● Use a soft cloth slightly moistened with a mild
detergent solution. Do not use a solution
containing alcohol, spirits, ammonia or abrasives.
Cleaning Discs
● When a disc becomes dirty, clean it with a
cleaning cloth. Wipe the disc from the center out.
Do not wipe in a circular motion.
● Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
23
Language Code
These pages can be used to select other languages.This does not affect the options in
“Audio”, “Subtitle” or “Disc Menu”.
Abkhazian
Afar
Afrikaans
Albanian
Amharic
6566
6565
6570
8381
6577
6582
7289
6583
6569
6589
6590
6665
6985
6669
6678
6672
6673
7866
6683
6682
6671
7789
6983
6765
6772
6769
German
Gikuyu; Kikuyu
Greek,
Guarani
Gujarati
Hausa
Hebrew
Herero
Hindi
6869
7573
6976
7178
7185
7265
7269
7290
7273
7279
7285
7383
7379
7368
7365
7369
7385
7375
7165
7384
7465
7486
7576
7578
7583
7575
7577
7573
8287
7589
7586
7579
7574
7585
7574
7679
7665
7686
7666
7673
7673
7673
7678
7684
7666
7775
7771
7783
7776
7784
7186
Arabic
Armenian
Assamese
Avestan
Aymara
Azerbaijani
Bashkir
Basque
Belarusian
Bengali
Bihari
Bislama
Bokmål, Norwegian
Bosnian
Breton
Bulgarian
Burmese
Castilian, Spanish
Catalan
Chamorro
Chechen
Chewa; Chichewa; Nyanja 7889
Chichewa; Chewa; Nyanja 7889
Chinese
Chuang; Zhuang
Church Slavic; Slavonic;
Church Slavonic; Church
Chuvash
Cornish
Corsican
Croatian
Czech
Danish
Dutch
Dzongkha
English
Esperanto
Estonian
Faroese
Fijian
Finnish
French
Frisian
Gaelic; Scottish Gaelic
Gallegan
Hiri Motu
Hungarian
Icelandic
Ido
Indonesian
Interlingua (International)
Interlingue
Inuktitut
Inupiaq
Irish
Italian
Japanese
Javanese
Kalaallisut
Kannada
Kashmiri
Kazakh
Khmer
Kikuyu; Gikuyu
Kinyarwanda
Kirghiz
Komi
Korean
Kuanyama; Kwanyama
Kurdish
Kwanyama; Kuanyama
Lao
Latin
Latvian
Letzeburgesch;
Limburgan; Limburger;
Limburger; Limburgan;
Limburgish; Limburger;
Lingala
Lithuanian
Luxembourgish;
Macedonian
Malagasy
Malay
9072
9065
6785
6785
6786
7587
6779
7282
6783
6865
7876
6890
6978
6979
6984
7079
7074
7073
7082
7089
7168
7176
7565
Malayalam
Maltese
Manx
Georgian
24
Language Code
These pages can be used to select other languages.This does not affect the options in
“Audio”, “Subtitle” or “Disc Menu”.
Maori
Marathi
7773
7782
7772
7779
7778
7865
7886
7886
7868
7882
7871
7869
8369
7868
7879
Sotho, Southem
South Ndebele
Spanish; Castilian
Sundanese
Swahili
8384
7882
6983
8385
8387
8383
8386
8476
8489
8471
8465
8484
8469
8472
6679
8473
8479
8483
8478
8482
8475
8487
8571
8575
8582
8590
8673
8679
8765
6789
8779
8872
8973
8979
9065
9085
Marshallese
Moldavian
Mongolian
Nauru
Navaho, Navajo
Navajo; Navaho
Ndebele, North
Ndebele, South
Ndonga
Swati
Swedish
Tagalog
Tahitian
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga (Tonga Islands)
Tsonga
Tswana
Turkish
Turkmen
Twi
Uighur
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Walloon
Welsh
Nepali
Northern Sami
North Ndebele
Norwegian
Norwegian Bokmål; Bokmål, 7866
Norwegian Nynorsk; 7878
Nyanja; Chichewa; Chewa 7889
Nynorsk, Norwegian; 7878
Occitan (post 1500); Proven 7967
Old Bulgarian; Old Slavonic; 6785
Old Church Slavonic; Old
Old Slavonic; Church
Oriya
6785
6785
7982
7977
7983
7983
8073
8065
7065
8076
8084
7967
8083
8185
8277
8279
8278
8285
8377
8371
8365
8367
7168
8382
8378
8368
8373
8375
8376
8379
Oromo
Ossetian; Ossetic
Ossetic; Ossetian
Pali
Panjabi
Persian
Polish
Wolof
Xhosa
Yiddish
Yoruba
Zhuang; Chuang
Zulu
Portuguese
Provençal; Occitan (post)
Pushto
Quechua
Raeto-Romance
Romanian
Rundi
Russian
Samoan
Sango
Sanskrit
Sardinian
Scottish Gaelic; Gaelic
Serbian
Shona
Sindhi
Sinhalese
Slovak
Slovenian
Somali
25
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
YAMAHA CORPORATION
IP
Printed in China
3139 246 12401
|
